Choose a MAPEI product below to calculate how much you'll need for your project:
- Caulks, sealants and joint fillers
- Grout
- Levelers and toppings
- Mortar beds and concrete repair mortars
- Patches and skimcoats
- Primers and coatings
- Sheet membranes and reinforcing meshes and fabrics
- Tile mortars and adhesives
Caulks, sealants and joint fillers

Mapesil T Plus
100%-Silicone Sealant with Enhanced Adhesion for Heavy Traffic and Expansion/Movement Joints
Mapesil T Plus is a professional-grade, 100%-silicone sealant with enhanced adhesion for use on multiple substrates. This product is specifically formulated for heavy traffic and expansion/movement joints exceeding both ASTM and ANSI standards.
Grout

Keracolor S Sanded Grout
Premium Sanded Grout with Polymer
Keracolor S Sanded Grout is a premium-grade, pre-blended, polymer-modified sanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/8" to 5/8" (3 to 16 mm).

Keracolor U Unsanded Grout
Premium Unsanded Grout with Polymer
Keracolor U Unsanded Grout is a premium-grade, preblended, polymer-modified unsanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/16" to 1/8" (1.5 to 3 mm).

MAPEI Flexcolor CQ
Ready-to-Use Grout with Color-Coated Quartz
MAPEI Flexcolor CQ is a professional-grade, ready-to-use specialty grout for precision commercial and residential installations with porcelain, ceramic and natural-stone tiles. MAPEI Flexcolor CQ can be used to grout interior/exterior tile, and its dense composition helps to prevent water-based stains by providing water repellency to the grout surface. MAPEI Flexcolor CQ is formulated with the latest innovation in quartz aggregate, which ensures color consistency, ease of cleanability and improved workability. In addition, this grout can be used on sensitive tile surfaces once tested, requires no sealer and cures naturally from evaporation of the low level of water in the formulation.
Comparison testing of MAPEI Flexcolor CQ versus traditional Portland-cement grout has verified that MAPEI Flexcolor CQ is 30% more cost-efficient (based on typical rates of installers) and requires 65% less time to install.

Ultracolor Plus FA
Rapid-Setting, “All-in-One” Grout Replacement for Sanded and Unsanded Grouts
Ultracolor Plus FA with DropEffect™ technology is an ultra premium, fine-aggregate, fast-setting, polymer-modified, color-consistent, nonshrinking, efflorescence-free grout for joint widths from 1/16" to 3/4" (1.5 to 19 mm). DropEffect reduces surface absorption to help repel water, dirt and grime from penetrating grout joints. Ultracolor Plus FA is specially formulated with MAPEI’s High-Hydrated Cement Technology (HCT™) to eliminate the common problems related to Portland-cement grout, such as color consistency and efflorescence. Along with offering higher polymer content, HCT reduces absorption and increases stain resistance when compared with standard-performance cement grouts.

Ultracolor Plus Max
High-Performance, Rapid-Setting Grout with Maximized Color Depth and Color Consistency
Ultracolor Plus Max is an ultra premium, fast-setting, polymer-modified, nonshrinking grout that offers rich and vibrant colors with maximized color depth and color consistency. This fine-aggregate grout can be used for joint widths from 1/16" to 3/4" (1.5 mm to 19 mm). Ultracolor Plus Max includes DropEffect™ technology for reduced surface absorption, helping to repel water, dirt and grime from penetrating grout joints. It is also specially formulated with MAPEI’s High-Hydrated Cement Technology (HCT™) to provide advantages over traditional grout, such as eliminating efflorescence and increasing stain resistance.
Levelers and toppings

Self-Leveler Plus
Self-Leveling Underlayment
Self-Leveler Plus is a high-strength, regular-setting, cement-based, self-leveling underlayment, for use over interior concrete, plywood and other approved floor surfaces. Self-Leveler Plus is convenient and easy to use. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings.
AVAILABLE AT SELECT RETAIL LOCATIONS ONLY
Mortar beds and concrete repair mortars

4 to 1 Mud Bed Mix
Sand and Cement Mortar Mix
4 to 1 is a preblended mixture of finely graded sand and Portland cement used for thick-bed mortar installations. 4 to 1 flattens and levels an existing substrate before the installation of tile and stone.
Patches and skimcoats

Mapecem Quickpatch
High-Performance Concrete Patch
Mapecem Quickpatch is a high-performance, fast-setting, cementitious material used for the patching of concrete surfaces.

Planipatch
Fast-Setting, Polymer-Modified, Cement-Based Patching Compound
Planipatch is an ultra fast-drying, self-curing, polymer-modified, cement-based patching compound that rapidly develops high compressive strength. Use for smoothing, patching and filling cracks, holes, voids and depressions in concrete and approved wood underlayments prior to the installation of floor coverings. Floor coverings can be installed just 1 hour after application. Mix with Planipatch Plus™ to use as an embossing leveler or patch over properly prepared vinyl sheet goods, vinyl composition tile (VCT), cement terrazzo and residual cutback adhesive surfaces .
This product includes High-Hydrated Cement Technology (HCT™).

Planipatch mixed with Planipatch Plus
Primers and coatings

ECO Prim Grip
Multipurpose, Bond-Promoting Primer
ECO Prim Grip is a ready-to-use, low-VOC, synthetic resin-based primer with bond-promoting silica aggregates suspended in dispersion. It enhances the performance and adhesion of mortars to existing ceramics and difficult-to-bond-to substrates. Plus, it improves bonding of self-leveling underlayments (SLUs) and bonds of render coats over cementitious substrates. Suitable for a wide variety of substrates, ECO Prim Grip combines excellent versatility with an easy, low-odor application.

MAPEI SM Primer
Water-Based Primer for MAPEI Peel-and-Stick Membranes
MAPEI SM Primer is a ready-to-use, fast-drying, water-based, latex primer for use under MAPEI’s peel-and-stick sheet membranes on residential and commercial indoor or outdoor floors. MAPEI SM Primer greatly increases the bond of MAPEI’s peel-and-stick sheet membranes to concrete, plywood and other approved, properly prepared floors. It can be applied with a roller or brush, is white in color and dries clear.

Mapelastic AquaDefense
Premium Waterproofing and Crack-Isolation Membrane
Mapelastic AquaDefense is a premixed, advanced liquid-rubber, extremely quick-drying waterproofing and crack-isolation membrane for installation under ceramic tile or stone in residential, commercial and industrial environments. Mapelastic AquaDefense provides a thin, continuous barrier to protect adjacent rooms and floors below from water damage. For common problem areas like coves, corners, cracks and drains, it can be combined with MAPEI’s optional Reinforcing Fabric or Mapeband™ accessories (cove roll and drain flash) to provide additional protection. Mapelastic AquaDefense dries after about 30 to 50 minutes and is then ready to receive any MAPEI polymer or epoxy mortar. Mapelastic AquaDefense can be flood-tested after 12 hours of drying time, is IAPMO-listed for use as a shower-pan liner, and exceeds ANSI A118.10 and ANSI A118.12 standards.

Primer T
All-Purpose Primer for Self-Leveling Underlayments
Primer T is a low-VOC, water-based acrylic primer that enhances the performance and adhesion of self-leveling underlayments (SLUs) on nonabsorbent surfaces such as ceramic tile, vinyl composition tile (VCT), epoxy moisture barriers and adhesive residue, as well as profiled, absorbent surfaces. Suitable for a wide variety of substrates, Primer T combines excellent versatility with an easy, low-odor application.
Sheet membranes and reinforcing meshes and fabrics

Mapeguard 2
3-in-1 Membrane for Crack Isolation, Waterproofing and Sound Reduction
Mapeguard 2 is a next-generation, flexible, thin, 40-mil (1-mm) lightweight, load-bearing, fabric-reinforced “peel-and-stick” crack-isolation, waterproofing and vapor-control membrane. Mapeguard 2 helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" [10 mm] wide) from transmitting through grout, ceramic tile and natural stone. It also reduces the transmission of impact sound (footsteps, dropped objects, etc.) and airborne sound (voice, TV, etc.) through floors when installed under ceramic tile, stone or wood floor coverings.
Tile mortars and adhesives

Ceramic Tile Mortar
Polymer-Enriched Thin-Set Mortar
Ceramic Tile Mortar is a regular-setting, polymer-enriched (“modified”) mortar for installing tile and stone on floors and walls in thin-set applications.

Floor Tile Mortar
Thin-Set Mortar
Floor Tile Mortar is a dry-set (non-polymer-enriched or “unmodified”) mortar for installing floor tile in thin-set applications.

Large Format Floor & Wall Tile Mortar
Professional, Large-and-Heavy-Tile Mortar with Polymer
Large-Format Floor & Wall Tile Mortar is a polymer-enriched (“modified”) mortar ideal for installing large-format tile on floors, walls and countertops. This large-and-heavy-tile mortar is designed to bond and support large tile over a diverse range of substrates.

Large Format Floor Tile Mortar
Professional, Large-and-Heavy-Tile Mortar with Polymer, for Floors
Large-Format Floor Tile Mortar is a polymer-enriched (“modified”), large-and-heavy-floor-tile mortar (formerly “medium-bed mortar”) and thin-set mortar for floor applications of large-format tile. It is used to install ceramic tile, porcelain tile, quarry tile, Saltillo tile and natural-stone tile. Large-Format Floor Tile Mortar is designed to give better support under large-format tile.

Large Format Floor Tile Mortar mixed with Polymer Additive

Large Tile & Stone Mortar
Premium, Polymer-Enriched, Large-and-Heavy-Tile and Thin-Set Mortar
Large Tile & Stone Mortar is a premium, regular-setting, polymer-enriched (“modified”) large-and-heavy-tile-mortar that is ideal for installing large-format tile and stone on floors, walls and countertops. This mortar can also be used in thin-set applications to install smaller-format tile over a diverse range of substrates.

MAPEI Ultralite Mortar Pro
Professional, Lightweight Mortar with Polymer for Large and Heavy Tile
MAPEI Ultralite Mortar Pro is a professional-grade, lightweight, single-component thin-set mortar that can also be used for large-and-heavy-tile and non-sag applications. This polymer-modified mortar is formulated with Easy Glide Technology™ for ease of application. MAPEI Ultralite Mortar Pro’s unique Ultralite Technology™ provides twice the coverage of a standard thin-set mortar per pound/kg and contains more than 20% recycled content.

Mosaic & Glass Tile Mortar
Polymer-Enriched Thin-Set Mortar
Mosaic & Glass Tile Mortar is a regular-setting, polymer-enriched (“modified”), bright white, multipurpose mortar designed for installing sheet-mounted mosaic glass or stone tiles or individual tiles in thin-set applications.
AVAILABLE AT SELECT RETAIL LOCATIONS ONLY

Mosaic & Glass Tile Mortar mixed with Polymer Additive

Porcelain Tile Mortar
Polymer-Enriched Thin-Set Mortar
Porcelain Tile Mortar is a regular-setting, polymer-enriched (“modified”) mortar for installing a wide range of tile and stone over a diverse range of substrates in thin-set applications.
AVAILABLE AT SELECT RETAIL LOCATIONS ONLY

Premium Mortar
Premium Mortar is a premixed no-mess alternative to traditional thin-set mortars that require water and mixing. It is nonflammable and ready to use.
AVAILABLE AT SELECT RETAIL LOCATIONS ONLY

Rapid Setting Tile Mortar
Polymer-Enriched Thin-Set Mortar
Rapid Setting Tile Mortar is a rapid-setting, polymer-enriched (“modified”) mortar for installing a wide range of tile and stone over a diverse range of substrates in thin-set applications.

Type 1
Premium Tile Adhesive
Type 1 is a premium-grade, traditional, nonflammable, acrylic adhesive for setting glazed and unglazed ceramic and porcelain tiles on walls, floors and countertops. This adhesive is used for interior applications only.

Uncoupling Membrane Mortar
Premium, Large-and-Heavy-Tile and Thin-Set Mortar
Uncoupling Membrane Mortar is a dry-set mortar for use in large-and-heavy-tile and thin-set applications for installing tile on floors and walls.
