Choose a MAPEI product below to calculate how much you'll need for your project:
- Caulks, sealants and joint fillers
- Levelers and toppings
- Mortar beds and concrete repair mortars
- Patches and skimcoats
- Primers and coatings
- Sheet membranes and reinforcing meshes and fabrics
- Tile mortars and adhesives
Caulks, sealants and joint fillers
Premium, Sanded and Unsanded Siliconized Acrylic Caulks
Keracaulk S (sanded) and Keracaulk U (unsanded) are premium-grade, easy-to-use, easy-to-clean siliconized acrylic caulks formulated to match all of MAPEI's grout colors.
Premium, Sanded and Unsanded Siliconized Acrylic Caulks
Keracaulk S (sanded) and Keracaulk U (unsanded) are premium-grade, easy-touse, easy-to-clean siliconized acrylic caulks formulated to match all of MAPEI's grout colors.
100%-Silicone Sealant for Heavy Traffic and Movement Joints
Mapesil T is a professional-grade, 100%-silicone sealant for use on multiple substrates. This product is specifically formulated for heavy traffic and expansion/movement joints and meets ASTM standards.
Premium Sanded Grout with Polymer
Keracolor S Sanded Grout is a premium-grade, pre-blended, polymer-modified sanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/8" to 5/8" (3 to 16 mm).
Premium Unsanded Grout with Polymer
Keracolor U Unsanded Grout is a premium-grade, preblended, polymer-modified unsanded Portland-cement tile grout that requires only the addition of water for mixing. It will grout joints from 1/16" to 1/8" (1.5 to 3 mm).
Premium Epoxy Grout and Mortar with Color-Coated Quartz
Kerapoxy CQ is an improved, two-component, 100%-solids epoxy grout and mortar that is nonsagging/nonslumping in joints up to 3/8" (10 mm) in width, water-cleanable and easy to apply. Kerapoxy CQ uses a proprietary aggregate to achieve its durable color, making it excellent for countertops, high-traffic areas, and areas needing stain and chemical resistance. Easy to maintain, Kerapoxy CQ will clean to the original color and contains BioBlockR technology to help protect against mold and mildew.
MAPEI Flexcolor 3D
Ready-to-Use, Translucent Grout with an “Iridescent Effect” Finish
MAPEI Flexcolor 3D is a professional-grade, ready-to-use (RTU) translucent specialty grout with an “iridescent effect” finish. It is offered in 10 designer colors with translucent characteristics that not only reflect but also refract light. This allows the grout to transition in color to complement the tile color. The “translucent effect” is most noticeable with the color Crystal Moon (#201), while the other nine colors exhibit a more pronounced “iridescent effect.”
MAPEI Flexcolor 3D is also formulated for commercial and residential interior installations of porcelain, ceramic, glass and natural-stone tiles. Plus, the dense surface structure of the grout helps to prevent water-based stains on the grout surface.
MAPEI Flexcolor 3D is formulated with the latest innovation in recycled glass-bead aggregate, which ensures color consistency, ease of cleanability and improved workability. In addition, this grout can be used on sensitive tile surfaces once tested, requires no sealer and cures naturally from evaporation.
Comparison testing of MAPEI Flexcolor 3D versus traditional Portland-cement grout has verified that MAPEI Flexcolor 3D requires 65% less time to install than powder grouts.
MAPEI Flexcolor CQ
Ready-to-Use Grout with Color-Coated Quartz
MAPEI Flexcolor CQ is a professional-grade, ready-to-use specialty grout for precision commercial and residential installations with porcelain, ceramic and natural-stone tiles. MAPEI Flexcolor CQ can be used to grout interior/exterior tile, and its dense composition helps to prevent water-based stains by providing water repellency to the grout surface. MAPEI Flexcolor CQ is formulated with the latest innovation in quartz aggregate, which ensures color consistency, ease of cleanability and improved workability. In addition, this grout can be used on sensitive tile surfaces once tested, requires no sealer and cures naturally from evaporation of the low level of water in the formulation.
Comparison testing of MAPEI Flexcolor CQ versus traditional Portland-cement grout has verified that MAPEI Flexcolor CQ is 30% more cost-efficient (based on typical rates of installers) and requires 65% less time to install.
Ultracolor Plus FA
Rapid-Setting, “All-in-One” Grout Replacement for Sanded and Unsanded Grouts
Ultracolor Plus FA with DropEffect™ technology is an ultra premium, fine-aggregate, fast-setting, polymer-modified, color-consistent, nonshrinking, efflorescence-free grout for joint widths from 1/16" to 3/4" (1.5 to 19 mm). DropEffect reduces surface absorption to help repel water, dirt and grime from penetrating grout joints. Ultracolor Plus FA is specially formulated with MAPEI’s High-Hydrated Cement Technology (HCT™) to eliminate the common problems related to Portland-cement grout, such as color consistency and efflorescence. Along with offering higher polymer content, HCT reduces absorption and increases stain resistance when compared with standard-performance cement grouts.
Ultracolor Plus Max
High-Performance, Rapid-Setting Grout with Maximized Color Depth and Color Consistency
Ultracolor Plus Max is an ultra premium, fast-setting, polymer-modified, nonshrinking grout that offers rich and vibrant colors with maximized color depth and color consistency. This fine-aggregate grout can be used for joint widths from 1/16" to 3/4" (1.5 mm to 19 mm). Ultracolor Plus Max includes DropEffect™ technology for reduced surface absorption, helping to repel water, dirt and grime from penetrating grout joints. It is also specially formulated with MAPEI’s High-Hydrated Cement Technology (HCT™) to provide advantages over traditional grout, such as eliminating efflorescence and increasing stain resistance.
Levelers and toppings
Ultraplan 1 Plus
High-Performance, Quick-Setting, Self-Leveling Underlayment
Ultraplan 1 Plus is a quick-setting, self-leveling, self-drying underlayment and repair mix for interior concrete and engineer-approved floors. Ultraplan 1 Plus has high strength and is abrasion-resistant, able to withstand light foot traffic after 2 to 3 hours and vehicular rubber-wheel traffic after 3 days.
Mortar beds and concrete repair mortars
4 to 1 Mud Bed Mix
Sand and Cement Mortar Mix
4 to 1 is a preblended mixture of finely graded sand and Portland cement used for thick-bed mortar installations. 4 to 1 flattens and levels an existing substrate before the installation of tile and stone.
Patches and skimcoats
High-Performance Concrete Patch
Mapecem Quickpatch is a high-performance, fast-setting, cementitious material used for the patching of concrete surfaces.
Fast-Setting, Polymer-Modified, Cement-Based Patching Compound
Planipatch is an ultra fast-drying, self-curing, polymer-modified, cement-based patching compound that rapidly develops high compressive strength. Use for smoothing, patching and filling cracks, holes, voids and depressions in concrete and approved wood underlayments prior to the installation of floor coverings. Floor coverings can be installed just 1 hour after application. Mix with Planipatch Plus™ to use as an embossing leveler or patch over properly prepared vinyl sheet goods, vinyl composition tile (VCT), cement terrazzo and residual cutback adhesive surfaces .
This product includes High-Hydrated Cement Technology (HCT™).
High-Performance, Fiber-Reinforced Skimcoating Compound
Planiprep SC is a high-performance, polymer-modified, fiber-reinforced cement-based skimcoating and patching compound. Use Planiprep SC to skimcoat and smooth minor surface variations and defects on common substrates. Planiprep SC creates a strong, durable surface ready for almost any floor application. Its unique formulation mixes easily with water and produces an easy-to-apply patching compound. Rapid-setting Planiprep SC allows for fast-track flooring installations in 30 to 60 minutes after application, depending on thickness and environmental conditions.
Primers and coatings
ECO Prim Grip
Multipurpose, Bond-Promoting Primer
ECO Prim Grip is a ready-to-use, low-VOC, synthetic resin-based primer with bond-promoting silica aggregates suspended in dispersion. It enhances the performance and adhesion of mortars to existing ceramics and difficult-to-bond-to substrates. Plus, it improves bonding of self-leveling underlayments (SLUs) and bonds of render coats over cementitious substrates. Suitable for a wide variety of substrates, ECO Prim Grip combines excellent versatility with an easy, low-odor application.
MAPEI SM Primer
Water-Based Primer for MAPEI Peel-and-Stick Membranes
MAPEI SM Primer is a ready-to-use, fast-drying, water-based, latex primer for use under MAPEI’s peel-and-stick sheet membranes on residential and commercial indoor or outdoor floors. MAPEI SM Primer greatly increases the bond of MAPEI’s peel-and-stick sheet membranes to concrete, plywood and other approved, properly prepared floors. It can be applied with a roller or brush, is white in color and dries clear.
Premium Waterproofing and Crack-Isolation Membrane
Mapelastic AquaDefense is a premixed, advanced liquid-rubber, extremely quick-drying waterproofing and crack-isolation membrane for installation under ceramic tile or stone in residential, commercial and industrial environments. Mapelastic AquaDefense provides a thin, continuous barrier to protect adjacent rooms and floors below from water damage. For common problem areas like coves, corners, cracks and drains, it can be combined with MAPEI’s optional Reinforcing Fabric or Mapeband™ accessories (cove roll and drain flash) to provide additional protection. Mapelastic AquaDefense dries after about 30 to 50 minutes and is then ready to receive any MAPEI polymer or epoxy mortar. Mapelastic AquaDefense can be flood-tested after 12 hours of drying time, is IAPMO-listed for use as a shower-pan liner, and exceeds ANSI A118.10 and ANSI A118.12 standards.
All-Purpose Primer for Self-Leveling Underlayments
Primer T is a low-VOC, water-based acrylic primer that enhances the performance and adhesion of self-leveling underlayments (SLUs) on nonabsorbent surfaces such as ceramic tile, vinyl composition tile (VCT), epoxy moisture barriers and adhesive residue, as well as profiled, absorbent surfaces. Suitable for a wide variety of substrates, Primer T combines excellent versatility with an easy, low-odor application.
Sheet membranes and reinforcing meshes and fabrics
3-in-1 Membrane for Crack Isolation, Waterproofing and Sound Reduction
Mapeguard 2 is a next-generation, flexible, thin, 40-mil (1-mm) lightweight, load-bearing, fabric reinforced “peel-and-stick” crack-isolation, waterproofing and vapor-control membrane. Mapeguard 2 helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" [10 mm] wide) from transmitting through grout, ceramic tile and natural stone. It also reduces the transmission of impact sound (footsteps, dropped objects, etc.) and airborne sound (voice, TV, etc.) through floors when installed under ceramic tile, stone or wood floor coverings.
All-in-One Membrane for Crack Isolation, Sound Reduction, Waterproofing and Vapor Management
Mapesonic 2 is a patented, next-generation, flexible, 76-mil thin, lightweight, load-bearing, fabric-reinforced, “peel-and-stick” membrane for sound reduction, crack isolation, waterproofing and vapor management. Application of Mapesonic 2 can be immediately followed by installation of finished flooring.
Mapesonic 2 reduces transmission of impact sound (such as footsteps and dropped objects) and airborne sound (such as voice and TV) through floors when installed under ceramic tile, stone, vinyl and wood floorings. It also helps to prevent existing or future in-plane floor cracks (with movement up to 3/8" or 10 mm wide) from transmitting through grout, ceramic tile and natural-stone assemblies.
Tile mortars and adhesives
Adesilex P10 Mosaic & Glass Tile
Premium Mosaic and Glass Tile Mortar with Polymer
Adesilex P10 Mosaic & Glass Tile is a premium-grade, bright white, multipurpose thin-set mortar formulated with non-sag properties. Adesilex P10 Mosaic & Glass Tile is designed for glass tile, glass mosaic and marble mosaic, and is ideal for light translucent natural stone.
Adesilex P10 Mosaic and Glass Tile Mortar mixed with Keraply
Professional, Extra Smooth, Large-and-Heavy-Tile Mortar with Polymer
Keraflex Plus is a highly versatile, non-sag/nonslump, large-and-heavy-tile mortar and thin-set mortar for tile and stone installations on floors, walls and countertops. This polymer-modified mortar is formulated with Easy Glide Technology™ for ease of application and offers excellent adhesion to substrates and tile. It can also be used as a mortar over uncoupling, crack-isolation, sound-reduction and waterproofing membranes.
Standard, Extra Smooth, Large-and-Heavy-Tile Mortar with Polymer
Keraflex SG is a standard-grade, versatile, large-and-heavy-tile mortar and thin-set mortar for tile and stone installations on floors, walls and countertops. It is formulated as non-sag for walls and nonslump for floors. Keraflex SG is a polymer-modified mortar formulated with Easy Glide Technology™ for ease of application and offers good adhesion to substrates and tile. It can also be used as a mortar over uncoupling, crack-isolation, sound-reduction and waterproofing membranes.
Standard Tile Mortar
Keraflor is a dry-set mortar for use in interior/exterior residential and light commercial floor applications.
Premium, 100%-Solids Epoxy Setting Mortar
Kerapoxy 410 is a two-component, solvent-free, 100%-solids epoxy setting floor and wall mortar that is suited for areas where most chemical-resistant setting material is necessary. It also has high compressive strength, which provides excellent impact strength in commercial facilities. Kerapoxy 410 is designed for setting most types of tile and stone.
MAPEI Ultralite Mortar
Premium, Lightweight Mortar with Polymer for Large and Heavy Tile
MAPEI Ultralite Mortar is a premium-grade, lightweight, single-component thin-set mortar that can also be used for large-and-heavy-tile and non-sag applications. This high-performance, polymer-modified mortar is formulated with Easy Glide Technology™ for ease of application, with Universal Color Formula™ for installing light-colored stones and translucent marble, and with BioBlock® technology for mold and mildew resistance. MAPEI Ultralite Mortar utilizes Ultralite Technology™ for twice the coverage of a standard thin-set mortar per pound/kg and contains more than 20% recycled content.
Premium Mortar is a premixed no-mess alternative to traditional thin-set mortars that require water and mixing. It is nonflammable and ready to use.
AVAILABLE AT SELECT RETAIL LOCATIONS ONLY
Premium Tile Adhesive
Type 1 is a premium-grade, traditional, nonflammable, acrylic adhesive for setting glazed and unglazed ceramic and porcelain tiles on walls, floors and countertops. This adhesive is used for interior applications only.
Ultrabond ECO GPT
Hybrid-Polymer-Based Adhesive for Gauged Porcelain Tile
Ultrabond ECO GPT is a single-component, non-sag, easy-to-trowel, hybridpolymer-based adhesive technology specially designed for the installation of gauged porcelain tile and gauged porcelain tile panels/slabs on interior vertical surfaces and countertops. Unique technology advancements are incorporated in the formulation of Ultrabond ECO GPT for delivering instant grab, while allowing for the needed adjustability of panels and large-format tile. Superior bonding performance is complemented with flexibility, deformability and quick-curing characteristics to meet the demands of installing gauged porcelain tile, panels and slabs with application-friendly properties.
Standard Tile Mortar with Polymer
Ultraflex 1 is a standard-grade, single-component, polymer-modified thin-set mortar for most interior and exterior installations of tile. This mortar has an above average content of unique dry polymer, resulting in good adhesion to the substrate and tile. Ultraflex 1 can be used for both interior and exterior installations of tile in most residential floor and wall applications. In commercial applications, use on interior floor and wall installations and exterior floors. Ultraflex 1 meets or exceeds ANSI A118.4 and ANSI A118.11 requirements when mixed with water.
Premium, Large-and-Heavy-Tile Mortar with Polymer
Ultraflex LFT is a premium, non-sag, large-and-heavy-tile mortar and thin-set mortar designed for large-format and heavy tile and stone for interior/exterior floor, wall and countertop installations. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. It is formulated with Easy Glide Technology™ for ease of application.
Ultraflex LFT Rapid
Premium, Rapid-Setting, Large-and-Heavy-Tile Mortar with Polymer
Ultraflex LFT Rapid is a premium, rapid-setting, non-sag, large-and-heavy-tile mortar (formerly known as “medium-bed mortar”) and thin-set mortar for large and heavy tile and stone for interior/exterior floor, wall and countertop installations. This mortar has a high content of unique dry polymer, resulting in excellent adhesion to the substrate and tile. Thanks to MAPEI’s High-Hydrated Cement Technology (HCT™), Ultraflex LFT Rapid offers superior drying-out characteristics for quick curing and does not contribute to efflorescence. Ultraflex LFT Rapid is FastTrack Ready™, allowing grouting in 3 to 4 hours.
Ultraflex LHT SG
Standard, Large-and-Heavy-Tile Mortar with Polymer
Ultraflex LHT SG is a standard-grade, non-sag, nonslump, polymer-modified, large-and-heavy-tile mortar and thin-set mortar for interior/exterior installations on floors, walls and countertops. It is used to install large-format and heavy tile/stone, including porcelain tile, heavy-ribbed-back tile, brick pavers, dimensional tile and natural-stone tile. Ultraflex LHT SG is designed for use at 3/32" to 1/2" (2.5 to 12 mm) thickness to give better support under large-format tile. This mortar is formulated with Easy Glide Technology™ for ease of application and good adhesion to the substrate and tile.